设备介绍：

该类型喷砂房的设计可解决贵公司不同种类的基材且外形较大的工件涂层前处理干喷砂而设计的喷砂设备，操作人员 只需将产品固定到挂架台车上，推入喷砂机舱、一键启动后工件自动进入喷砂室内进行自动喷砂后，通过自动切换吹净工作 将自动清理工件上的残留粉尘，产品流出喷砂系统外，如此连续循环工作。

适合使用磨料为：棕刚玉、白刚玉、玻璃珠、钢砂丸等。

适合使用砂料粒度为：24-300目。

主机设计使用寿命为：6年。

本机配置2组自动喷砂罐体，2把高压型自动喷砂枪，喷砂枪分布装置在连接喷砂罐体下方部位，可通过快速切换喷砂 管至不同砂罐出砂系统部位，喷枪装置在6轴机器人之手臂上实现全自动360度无死角喷砂作业，其中有一把喷砂枪安装在 专用独立喷砂系统之上，作为手动补喷专用喷砂系统。

The design of this type of sandblasting room can solve your company's sandblasting equipment designed for dry sandblasting of different kinds of substrates and large-sized workpieces before coating. Operators only need to fix the products on the rack trolley, push them into the sandblasting cabin, and after one-click start, the workpieces will automatically enter the sandblasting room for automatic sandblasting, and then the residual dust on the workpieces will be automatically cleaned by automatically switching the blowing work, and the products will flow out of the sandblasting system, thus continuously circulating.

 Suitable abrasives are brown corundum, white corundum, glass beads, steel shot, etc.

 Suitable sand size is 24-300 mesh.

 The designed service life of the host is 6 years.

 This machine is equipped with two groups of automatic sandblasting tanks and two high-pressure automatic sandblasting guns. The sandblasting gun distribution device is located at the lower part of the connected sandblasting tank, and the sandblasting pipe can be quickly switched to different sandblasting system parts of the sandblasting tank. The sandblasting gun device can realize full-automatic 360-degree sandblasting without dead angle on the arm of a 6-axis robot, and one sandblasting gun is installed on a special independent sandblasting system as a special sandblasting system for manual supplementary spraying.

工作原理

运用蜂窝式吸砂地板技术，采用气力输送原理，利用风机负压产生的空气动力将砂料回收，再通过管道吸送到砂尘分 离器中进行分离，分离出来的有用砂料自动落入喷砂压力罐，参与下一个喷砂会后的循环；分选出来的破碎砂料、焊渣、 氧化皮、粉尘等无用杂物则自动进入除尘系统进行过滤.同时为保证喷砂工人在喷砂作业中能够有足够清晰的工作视线，本套 系统配置了高效的滤筒除尘器,采用科学的吸尘方式，将在喷砂作业时参生的粉尘迅速的吸入抽尘管道,并通过高效除尘器进 行过滤，排放的尾气符合国家环保要求。

Using honeycomb sand suction floor technology and pneumatic conveying principle, the sand materials are recovered by using the aerodynamic force generated by the negative pressure of the fan, and then sucked into the sand dust separator through the pipeline for separation. The separated useful sand materials automatically fall into the sand blasting pressure tank and participate in the cycle after the next sand blasting meeting. The separated broken sand, welding slag, scale, dust and other useless sundries will automatically enter the dust removal system for filtration. At the same time, in order to ensure that sandblasting workers can have a clear enough line of sight during sandblasting, this system is equipped with an efficient filter cartridge dust collector, which adopts a scientific dust collection method to quickly suck the dust generated during sandblasting into the dust suction pipe and filter it through the efficient dust collector. The exhaust gas discharged meets the national environmental protection requirements.